An environmental affable, economically feasible and reusable sulfonated adsorbent were constructed by gamma radiation grafting of glycidyl methacrylate (GMA) on non-woven polyethylene fabric and subsequent chemical modification. Highest graft yield of 343.31% was obtained at favourable conditions: 30 kGy radiation dose, 5% monomer concentration, adding up of 0.5% Tween-20 as an additive, 4 h reaction time. The epoxide group containing GMA-g-PE film were functionalized through sulfonation. The adsorbent was identified by Fourier Transform Infrared (FTIR), Scanning Electron Microscopy (SEM) and Thermo-gravimetric Analysis (TGA). The aqueous solutions of methylene blue were prepared in various concentrations and adsorption behavior by the developed sulfonated-GMA-g-PE film were investigated. MB uptake capacity at different environment such as contact time, pH and initial MB concentration were identified. The adsorption of MB is highly pH dependent and utmost sorption was found at pH 7. The kinetic adsorption data were interpreted by pseudo-first-order and pseudo-second-order equations. Pseudo-first-order rate kinetic model is more applicable for the sorption process due to its higher correlation coefficient. From the two isotherm model Langmuir and Fruendlich, Fruendlich model attuned best with the MB sorption as presented by higher correlation coefficient. The MB uptake capacity of the sorbent obtained from Langmuir model was 500 mg/g. Futhermore, the adsorbent could be reformed and reused repeatedly for the sorption of MB from waste water.
Published in | American Journal of Polymer Science and Technology (Volume 7, Issue 1) |
DOI | 10.11648/j.ajpst.20210701.11 |
Page(s) | 1-9 |
Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
Copyright |
Copyright © The Author(s), 2021. Published by Science Publishing Group |
Radiation, GMA, Methylene Blue, Isotherm, Kinetics
[1] | Ravikumar K, Deebika B, Balu K: Decolourization of aqueous dye solutions by a novel adsorbent: application of statistical designs and surface plots for the optimization and regression analysis. J. Hazard. Mater. 122, 75-93, 2005. |
[2] | Lee JW, Choi SP, Thiruvenkatachari R, Shim WG, Moon H: Evaluation of the performance of adsorption and coagulation processes for the maximum removal of reactive dyes. Dyes Pigm. 69, 196-203, 2006. |
[3] | Easton JR, Cooper P: Colour in Dye House Effluent (Alden, Oxford: The Society of Dyers and Colourists), pp. 9–21, 1995. |
[4] | Dutta PK: An overview of textile pollution and its remedy. Indian J. Environ. Prot. 14, 443-446, 1994. |
[5] | Oz M, Lorke DE, Petroianu GA: (2009) Methylene blue and Alzheimer’s disease. Biochem. Pharmacol. 78, 927-932, 2009. |
[6] | Tsai WT, Chang CY, Lin MC, Chien SF, Sun HF, Hsieh MF: Adsorption of acid dye onto activated carbons prepared from agricultural waste bagasse by ZnCl2 activation. Chemosphere 45, 51-58, 2001. |
[7] | Yener J, Kopac T, Dogu G, Dogu T: Adsorption of basic Yellow 28 from aqueous solutions with clinoptilolite and amberlite. J. Colloid Interf. Sci. 294, 255-264, 2006. |
[8] | Wang S, Boyjoo Y, Choueib A: A comparative study of dye removal using fly ash treated by different methods. Chemosphere 60, 1401-1407, 2005. |
[9] | Panswed J, Wongchaisuwan S: Mechanism of dye wastewater color removal by magnesium carbonate-hydrated basic. Water Sci. Technol. 18, 139–144, 1986. |
[10] | Ciardelli G, Corsi L, Marucci M: Membrane separation for wastewater reuse in the textile industry. Resour. Conserv. Recycl. 31, 189-197, 2000. |
[11] | Swaminathan K, Sandhya S, Carmalin Sophia A., Pachhade K, Subrahmanyam YV: Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system. Chemosphere 50, 619-625, 2003. |
[12] | Muthukumar M, Selvakumar N: Studies on the effect of inorganic salts on decolouration of acid dye effluents by ozonation. Dyes Pigm. 62, 221-228, 2004. |
[13] | Alinsafi A, Khemis M, Pons MN, Leclerc JP, Yaacoubi A, Benhammou A, Nejmeddine A: Electro-coagulation of reactive textile dyes and textile wastewater. Chem. Eng. Process 44, 461-470, 2005. |
[14] | Mall ID, Srivastava VC, Agarwal NK, Mishra IM: Removal of congo red from aqueous solution by bagasse fly ash and activated carbon: kinetic study and equilibrium isotherm analyses. Chemosphere 61, 492-501, 2005. |
[15] | Mitchell M, Ernst WR, Rasmussen ET, Bagherzadeh P, Lightsey GR: Adsorption of textile dyes by activated carbon produced from agricultural, municipal and industrial-wastes. Bull. Environ. Contam. Toxicol. 19, 307-311, 1978. |
[16] | Abd-Elhamid AI, Mohammed E, El-Sadek MH, ElShanshory AA, Soliman HMA, Akl MA, Rashad M: Enhanced removal of cationic dye by eco-friendly activated biocharderived from rice straw. Appl. Water Sci. 10, Article number: 45, 2020. |
[17] | Hamzezadeh A, Rashtbari Y, Afshin S, Morovati M, Vosoughi M: Application of low-cost material for dsorption of dye from aqueous solution,, Int. J. Environ. Anal. Chem. 2020. doi.org/10.1080/03067319.2020.1720011. |
[18] | Shabaan OA, Jahin HS, Mohamed GG: Removal of anionic and cationic dyes from wastewater by adsorption using multiwall carbon nanotubes. Arab. J. Chem. 13, 4797-4810, 2020. |
[19] | Yadav S, Asthana A, Chakraborty R, Jain B, Singh AK, Carabineiro SAC and Susan MABH: Cationic Dye Removal Using Novel Magnetic/Activated Charcoal/βCyclodextrin/Alginate Polymer Nanocomposite. Nanomaterials 10, 170, 2020 doi: 10.3390/nano10010170. |
[20] | Goel NK, Kumar V, Misra N, Vershney L: Cellulose based cationic adsorbent fabricated via radiation grafting process for treatment of dyes waste water. Carbohydr. Polym. 24 Jun 2015, 132, 444-451, 2015. DOI: 10.1016/j.carbpol.2015.06.054. |
[21] | Kumar R, Sharma RK, Singh AP: Synthesis and characterization of cellulose based graft copolymers with binary vinyl monomers for efficient removal of cationic dyes and Pb(II) ions. J. Polym. Res. 26, Article number: 135, 2019. |
[22] | Lertsarawut P, Hemvichian K, Rattanawongwiboon T, Suwanmala P: Dye adsorbent prepared by radiation-induced graft polymerization of acrylic acid onto carboxymethyl cellulose. J. Phys.: Conf. Ser. 1285 012023, 2019. |
[23] | Zhu L, Guan C, Zhou B: Adsorption of Dyes onto Sodium Alginate Graft Poly(Acrylic Acid-co-2-Acrylamide-2-Methyl Propane Sulfonic Acid)/ Kaolin Hydrogel Composite. Polym. Polym. Compos. 25, 627-634, 2017. |
[24] | Dong C, Li W, Yuhong M, Wantai Y: Super-adsorbent material based on functional polymer particles with a multilevel porous structure. NPG Asia Mater. 8, e301, 2016. |
[25] | Hsieh L, Shinawatra YM, Castillo MD: Postirradiation polymerization of vinyl monomers on poly(ethylene terephthalate). J. Appl. Polym. Sci. 31, 509-519, 1986. |
[26] | Bari EMA, Sarhan AA and Razik HHA: Effect of graft copolymerization of 2-hydroxyethyl methacrylate on the properties of polyester fibers and fabric. J. Appl. Polym. Sci. 35, 439-448, 1986. |
[27] | Nasef MM: Gamma radiation-induced graft copolymerization of styrene onto poly (ethylene terephthalate) films. J. Appl. Polym. Sci. 77, 1003-1012, 2000. |
[28] | Ke X, Drache M, Gohs U, kunz U, Beuermann S: Preparation of Polymer Electrolyte Membranes via Radiation-Induced Graft Copolymerization on Poly(ethylene-alt-tetrafluoroethylene) (ETFE) Using the Crosslinker N,N′-Methylenebis (acrylamide), Membranes 8 (4), 102, 2018 https://doi.org/10.3390/membranes8040102. |
[29] | He X., Male KB, Nesterenko PN, Brabazon D, Paull B, Luong JHT: Adsorption and desorption of methylene blue on porous carbon, monoliths and nanocrystalline cellulose. ACS Appl. Mater. Interfaces 5, 8796-8804, 2013. |
[30] | Yang J, Qiu K: Preparation of activated carbons from walnut shells via vacuum chemical activation and their application for methylene blue removal. Chem. Eng. J., 165, 209-217, 2010. |
[31] | Bulut, Y, Aydın HA: A kinetics and thermodynamics study of methylene blue adsorption on wheat shells. Desalination 194, 259-267, 2006. |
[32] | Ponnusami V, Gunasekar V, Srivastava SN: Kinetics of methylene blue removal from aqueous solution using gulmohar (Delonix regia) plant leaf powder: Multivariate regression analysis. J. Hazard. Mater. 169, 119-127, 2009. |
[33] | Uddin MT, Islam MA, Mahmud S, Rukanuzzaman M: Adsorptive removal of methylene blue by tea waste. J. Hazard. Mater. 164, 53-60, 2009. |
[34] | Kavitha D, Namasivayam C: Experimental and kinetic studies on methylene blue adsorption by coir pith carbon. Bioresour. Technol. 98, 14-21, 2007. |
[35] | Senthilkumaar S, Varadarajan PR, Porkodi K, Subbhuraam CV: Adsorption of methylene blue onto jute fiber carbon: kinetics and equilibrium studies. J. Colloid Interf. Sci. 284, 78-82, 2005. |
[36] | Rahman N, Dafader NC, Marjub MM, SultanaS, Miah AR, Abser MN, Chowdhury U, Rahman MO: Efficiency of biodegradable acrylic acid-chitosan hydrogel in eliminating methylene blue from wastewater. J. Polym. Sci. Technol. 3, 5-10, 2018. |
APA Style
Md. Sohel Rana, Nazia Rahman, Tofail Ahmed Chowdhury, Nirmal Chandra Dafader, Shahnaz Sultana, et al. (2021). Application of Sulfonated GMA-g-non Woven PE Fabric for the Efficient Removal of Methylene Blue Dye from Wastewater. American Journal of Polymer Science and Technology, 7(1), 1-9. https://doi.org/10.11648/j.ajpst.20210701.11
ACS Style
Md. Sohel Rana; Nazia Rahman; Tofail Ahmed Chowdhury; Nirmal Chandra Dafader; Shahnaz Sultana, et al. Application of Sulfonated GMA-g-non Woven PE Fabric for the Efficient Removal of Methylene Blue Dye from Wastewater. Am. J. Polym. Sci. Technol. 2021, 7(1), 1-9. doi: 10.11648/j.ajpst.20210701.11
AMA Style
Md. Sohel Rana, Nazia Rahman, Tofail Ahmed Chowdhury, Nirmal Chandra Dafader, Shahnaz Sultana, et al. Application of Sulfonated GMA-g-non Woven PE Fabric for the Efficient Removal of Methylene Blue Dye from Wastewater. Am J Polym Sci Technol. 2021;7(1):1-9. doi: 10.11648/j.ajpst.20210701.11
@article{10.11648/j.ajpst.20210701.11, author = {Md. Sohel Rana and Nazia Rahman and Tofail Ahmed Chowdhury and Nirmal Chandra Dafader and Shahnaz Sultana and Md. Nabul Sardar and Md. Nahid Kayser}, title = {Application of Sulfonated GMA-g-non Woven PE Fabric for the Efficient Removal of Methylene Blue Dye from Wastewater}, journal = {American Journal of Polymer Science and Technology}, volume = {7}, number = {1}, pages = {1-9}, doi = {10.11648/j.ajpst.20210701.11}, url = {https://doi.org/10.11648/j.ajpst.20210701.11}, eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajpst.20210701.11}, abstract = {An environmental affable, economically feasible and reusable sulfonated adsorbent were constructed by gamma radiation grafting of glycidyl methacrylate (GMA) on non-woven polyethylene fabric and subsequent chemical modification. Highest graft yield of 343.31% was obtained at favourable conditions: 30 kGy radiation dose, 5% monomer concentration, adding up of 0.5% Tween-20 as an additive, 4 h reaction time. The epoxide group containing GMA-g-PE film were functionalized through sulfonation. The adsorbent was identified by Fourier Transform Infrared (FTIR), Scanning Electron Microscopy (SEM) and Thermo-gravimetric Analysis (TGA). The aqueous solutions of methylene blue were prepared in various concentrations and adsorption behavior by the developed sulfonated-GMA-g-PE film were investigated. MB uptake capacity at different environment such as contact time, pH and initial MB concentration were identified. The adsorption of MB is highly pH dependent and utmost sorption was found at pH 7. The kinetic adsorption data were interpreted by pseudo-first-order and pseudo-second-order equations. Pseudo-first-order rate kinetic model is more applicable for the sorption process due to its higher correlation coefficient. From the two isotherm model Langmuir and Fruendlich, Fruendlich model attuned best with the MB sorption as presented by higher correlation coefficient. The MB uptake capacity of the sorbent obtained from Langmuir model was 500 mg/g. Futhermore, the adsorbent could be reformed and reused repeatedly for the sorption of MB from waste water.}, year = {2021} }
TY - JOUR T1 - Application of Sulfonated GMA-g-non Woven PE Fabric for the Efficient Removal of Methylene Blue Dye from Wastewater AU - Md. Sohel Rana AU - Nazia Rahman AU - Tofail Ahmed Chowdhury AU - Nirmal Chandra Dafader AU - Shahnaz Sultana AU - Md. Nabul Sardar AU - Md. Nahid Kayser Y1 - 2021/01/15 PY - 2021 N1 - https://doi.org/10.11648/j.ajpst.20210701.11 DO - 10.11648/j.ajpst.20210701.11 T2 - American Journal of Polymer Science and Technology JF - American Journal of Polymer Science and Technology JO - American Journal of Polymer Science and Technology SP - 1 EP - 9 PB - Science Publishing Group SN - 2575-5986 UR - https://doi.org/10.11648/j.ajpst.20210701.11 AB - An environmental affable, economically feasible and reusable sulfonated adsorbent were constructed by gamma radiation grafting of glycidyl methacrylate (GMA) on non-woven polyethylene fabric and subsequent chemical modification. Highest graft yield of 343.31% was obtained at favourable conditions: 30 kGy radiation dose, 5% monomer concentration, adding up of 0.5% Tween-20 as an additive, 4 h reaction time. The epoxide group containing GMA-g-PE film were functionalized through sulfonation. The adsorbent was identified by Fourier Transform Infrared (FTIR), Scanning Electron Microscopy (SEM) and Thermo-gravimetric Analysis (TGA). The aqueous solutions of methylene blue were prepared in various concentrations and adsorption behavior by the developed sulfonated-GMA-g-PE film were investigated. MB uptake capacity at different environment such as contact time, pH and initial MB concentration were identified. The adsorption of MB is highly pH dependent and utmost sorption was found at pH 7. The kinetic adsorption data were interpreted by pseudo-first-order and pseudo-second-order equations. Pseudo-first-order rate kinetic model is more applicable for the sorption process due to its higher correlation coefficient. From the two isotherm model Langmuir and Fruendlich, Fruendlich model attuned best with the MB sorption as presented by higher correlation coefficient. The MB uptake capacity of the sorbent obtained from Langmuir model was 500 mg/g. Futhermore, the adsorbent could be reformed and reused repeatedly for the sorption of MB from waste water. VL - 7 IS - 1 ER -