| Peer-Reviewed

Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network

Received: 14 January 2022     Accepted: 4 February 2022     Published: 16 February 2022
Views:       Downloads:
Abstract

Biodiesel has been referred to as a perfect substitute for diesel fuel due to its numerous promising properties. They are renewable, clean, increases energy security, improves the environment and air quality and also provides some good safety benefits. This study is focused on the investigation of the use of natural heterogeneous catalysts for production of biodiesel from jansa seed oil, as well as the implementation of artificial neural network (ANN) for the prediction of biofuel yield and process parameters. The biodiesel was produced through transesterification reaction by reacting jansa seed oil (FFA) with methanol (alcohol) to yield methyl ester. Waste periwinkle shell was prepared in 3 different forms; raw, calcined and acidified. The percentage yield of the methyl ester obtained were calculated and tabulated. The process parameters considered were methanol-oil mole ratio, catalyst concentration, agitation speed, reaction temperature and reaction time. The results of this research work revealed that the calcined periwinkle shell catalyst produced higher yield of biodiesel, compared to the yield obtained from the raw and acidified catalyzed process. The properties of the fatty acid methyl esters were within the standard range. The experimental and predicted yield were marginally the same. Hence, the model accurately predicted the yield with acceptable coefficient of determination and low mean squared error (MSE). The results demonstrate the flexibility of ANN model and the improvement of the model in terms of performance prediction when solving problems with stochastic dataset, especially the transesterification of biodiesel.

Published in American Journal of Applied Chemistry (Volume 10, Issue 1)
DOI 10.11648/j.ajac.20221001.12
Page(s) 7-14
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2022. Published by Science Publishing Group

Keywords

Jansa Seed, Catalyst, Transesterification, Artificial Neural Network

References
[1] Eriola B., Samuel S. O., Sheriff O. A. and Olatunde S. O. (2015) Performance evaluation of artificial neural network coupled with generic algorithm and response surface methodology in modeling and optimization of biodiesel production process parameters from shea tree (Vitellaria paradoxa) nut butter. J. Renewable Energy pp. 408-417.
[2] Ayoolaa A. A., Hymore F. K., Omonhinminc C. A., Olawole O. C., Fayomi O. S. I, Babatundea D. Fagbielea, O. (2019). Analysis of waste groundnut oil biodiesel production using response surface methodology and artificial neural network. J. Chemical Data Collections. 22 100238 pp. 1-9.
[3] Ayoola, A. A., Adeniyi, D. O., Sanni, S. E., Osakwe, K. I. and Jato, J. D. (2018). Investigating production parameters and impacts of potential emissions from soybean biodiesel stored under different conditions, Env. Eng. Res. 23 (1) (2018) 54–61.
[4] Otori, A. A., Mann, A., Suleiman. M. A. T., and Egwim, E. C (2019). Synthesis of Heterogeneous Catalyst from Waste Snail Shells for Biodiesel Production using Afzelia africana Seed Oil. Nigerian Journal of Chemical Research vol. (23) pp. 35-51.
[5] Fang Y., Zhen-hong Y., Peng-mei, L., Wen, L., Ling-mei, Y., Li, D. (2010). Synthesis of biodiesel by Fe (II)-Zn double-metal cyanide complexes, J. Fuel Chem. Tech. 38 (3) 281–286.
[6] Tayari S., Abedi R., Rahi A. (2020). Comparative assessment of engine performance and emissions fueled with three different biodiesel generations Renew. Energy. vol. (147) pp. 1058-1069.
[7] Avinash P. I., Anuj K. C., Rafael P., Sabrina E. M and Silvio S. S. (2020) Advances in Nanocatalysts Mediated Biodiesel Production: A Critical Appraisal. Symmetry vol. 12, pp 1-21.
[8] Palaniappan, K. (2017). An overview of applications of nanotechnology in biofuel production. World Appl. Sci. J., 35, 1305–1311. 61.
[9] Khan, I.; Saeed, K.; Khan, I. Nanoparticles: Properties, applications and toxicities. Arab. J. Chem. 2019, 12, 908–931.
[10] Asfaram, A., Ghaedi, M., Hajati, S. and Goudarzi, A. (2016) Synthesis of magnetic c-Fe2O3-based nanomaterial for ultrasonic assisted dyes adsorption: modeling and optimization, Ultrasonics Sonochem. vol. 32 pp. 418–431.
[11] Shemelis N. G. and Jorge Mario M. (2017) Review Biodiesel production technologies: review AIMS Energy. vol. (5) 425-457.
[12] Tabatabaei, M., Karimi, K., Sárvári, K H and Kumar, R (2015) Recent trends in biodiesel production Biofuel Res. J. vol. 7 pp. 258–267.
[13] Nwokonkwo. D. C., Nwaolisa S. U and Odo H. A (2016). Comparative Physicochemical Study of the Oils from the Seeds of Cussonia Bateri (JANSA) and Brasssica Juncea (MUSTARD). International Journal of Applied Chemistry. ISSN 0973-1792 Volume 12, Number 1 (2016) pp. 51-58.
[14] Ayoola, A. A., Hymore, F. K. and. Omonhinmin, C. A (2016) Optimization of biodiesel production from selected waste oils using response surface methodology Biotechnol. 16 (1) pp. 1–9.
[15] Ayoola, AA. Babalola, R., Ojewumi, M. E. and Fayomi, O. S I (2018) Assessment of KOH and NaOH catalysed biodiesel from melon seed oil. Mat. Focus 7 (5) pp. 650–656.
[16] Ayoola, A. A. (2015) Production and life cycle assessment of biodiesel produced from three waste oils Ph.D. Thesis, Chemical Engineering Department, Covenant University, Nigeria.
[17] Ikbal B. L., Kalyani R., Rajat G., Sushovan C., Bappi P. and Lalthazuala R. (2018) Waste snail shell derived heterogeneous catalyst for biodiesel production by the transesterification of soybean oil. Royal Society of Chemistry Advances DOI: 10.1039/c8ra02397b vol. 8, 20131–20142.
[18] Adnani, A. Basri, M., Chaibakhsh, N., Rahman, A. B. Salleh, Artificial neural network analysis of lipase-catalyzed synthesis of sugar alcohol ester, Ind. Crops Prod. 33 (1) (2011) 42–48.
[19] Babalola, P. O. Bolu, C. A. and Inegbenebor, A. O. (2017) “Artificial neural network prediction of aluminium metal matrix composite with silicon carbide particles developed using stir casting method,” http://ijens.org/Vol_17_I_06/154502-1706-7979-, pp. 151–159.
[20] Banerjee, A., Varshney, D. Kumar, S. Chaudhary, P. Gupta, V. K. (2017) Biodiesel production from castor oil: ANN modeling and kinetic parameter estimation, Int. J. Ind. Chem. 8 (3) 253–262.
[21] Beale M, Hagan M, Demuth H (2013) MATLAB Neural network toolbox user’s guide (R2013A).
[22] Ghaedi, A. M and Vafaei, A. (2017) Applications of artificial neural networks for adsorption removal of dyes from aqueous solution: a review, Adv. Colloid Interface Sci. vol. 245 pp. 20–39.
[23] Ahmadi, M. A., Zendehboudi, S., Lohi, A., Elkamel, A. and Chatzis, I. (2013) Application of hybrid genetic algorithm with particle swarm optimization and neural network for reservoir permeability prediction. J. Geophys. Prospect vol. 61 pp. 582–598.
[24] Mohammed I. J, Richard J. B, Wijitha S. 1, Ian M. O. and Zoran D. R. (2013). The Use of Artificial Neural Networks for Identifying Sustainable Biodiesel Feedstocks. Energies. vol. 6 pp. 3764-3806.
[25] Alkim, E., Gürbüz, E., Kılıç, E. (2012) A fast and adaptive automated disease diagnosis method with an innovative neural network model. Neural Network. vol. 330 pp. 88–96.
[26] Chaudhary P, Kumar B, Kumar S, Gupta VK (2015) Transesterification of castor oil with methanol—kinetic modeling. Chem Prod Process Model 10 (2): 71–80.
[27] Canoira L, Galean JG, Alcantara R, Lapuerta M, Contreras RG (2010) Fatty acid methyl esters (FAMEs) from castor oil: production process assessment and synergistic effects in its properties. Renew Energy 35: 208–217.
[28] M. O. Okwu, V. U. Chukwu and O. Oguoma (2019) Application of Artificial Neural Network Model for Cost Optimization in a Single, Multi-Destination System with Non- Deterministic Inputs. Advances in Computational Intelligence, Lecture Note in Computer Science book series (LNCS, Volume 11, 507) Springer.
[29] Encinar, J. M., Pardal, A., Sánchez, N. and Nogales, S. (2018) Biodiesel by transesterification of rapeseed oil using ultrasound: a kinetic study of base-catalysed reactions, Energies vol. 11 pp. 2229–2241.
[30] Khudsange, C. R. and Wasewar, K. L (2017). Experimental and modeling study of esterification reaction for synthesis of butyl butyrate: desirability function approach for optimization and prediction comparative study of RSM and ANN, Int. J. Chem. React. Eng. 15 (3) pp. 45–58.
[31] Sharifpour, E., Khafri, H. Z., Ghaedi, M., Asfaram, A. and Jannesar, R (2018). Isotherms and kinetic study of ultrasound-assisted adsorption of malachite green and Pb2+ ions from aqueous samples by copper sulfide nanorods loaded on activated carbon: experimental design optimization, Ultrasonics Sonochem. vol. 40 pp. 373–382.
Cite This Article
  • APA Style

    Chinwe Priscilla Okonkwo, Vincent Ishmael Egbulefu Ajiwe, Ebuka Chidiebere Mmaduakor, Njideka Veronica Nwankwo. (2022). Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network. American Journal of Applied Chemistry, 10(1), 7-14. https://doi.org/10.11648/j.ajac.20221001.12

    Copy | Download

    ACS Style

    Chinwe Priscilla Okonkwo; Vincent Ishmael Egbulefu Ajiwe; Ebuka Chidiebere Mmaduakor; Njideka Veronica Nwankwo. Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network. Am. J. Appl. Chem. 2022, 10(1), 7-14. doi: 10.11648/j.ajac.20221001.12

    Copy | Download

    AMA Style

    Chinwe Priscilla Okonkwo, Vincent Ishmael Egbulefu Ajiwe, Ebuka Chidiebere Mmaduakor, Njideka Veronica Nwankwo. Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network. Am J Appl Chem. 2022;10(1):7-14. doi: 10.11648/j.ajac.20221001.12

    Copy | Download

  • @article{10.11648/j.ajac.20221001.12,
      author = {Chinwe Priscilla Okonkwo and Vincent Ishmael Egbulefu Ajiwe and Ebuka Chidiebere Mmaduakor and Njideka Veronica Nwankwo},
      title = {Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network},
      journal = {American Journal of Applied Chemistry},
      volume = {10},
      number = {1},
      pages = {7-14},
      doi = {10.11648/j.ajac.20221001.12},
      url = {https://doi.org/10.11648/j.ajac.20221001.12},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajac.20221001.12},
      abstract = {Biodiesel has been referred to as a perfect substitute for diesel fuel due to its numerous promising properties. They are renewable, clean, increases energy security, improves the environment and air quality and also provides some good safety benefits. This study is focused on the investigation of the use of natural heterogeneous catalysts for production of biodiesel from jansa seed oil, as well as the implementation of artificial neural network (ANN) for the prediction of biofuel yield and process parameters. The biodiesel was produced through transesterification reaction by reacting jansa seed oil (FFA) with methanol (alcohol) to yield methyl ester. Waste periwinkle shell was prepared in 3 different forms; raw, calcined and acidified. The percentage yield of the methyl ester obtained were calculated and tabulated. The process parameters considered were methanol-oil mole ratio, catalyst concentration, agitation speed, reaction temperature and reaction time. The results of this research work revealed that the calcined periwinkle shell catalyst produced higher yield of biodiesel, compared to the yield obtained from the raw and acidified catalyzed process. The properties of the fatty acid methyl esters were within the standard range. The experimental and predicted yield were marginally the same. Hence, the model accurately predicted the yield with acceptable coefficient of determination and low mean squared error (MSE). The results demonstrate the flexibility of ANN model and the improvement of the model in terms of performance prediction when solving problems with stochastic dataset, especially the transesterification of biodiesel.},
     year = {2022}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Modelling and Optimization of Biodiesel Production Process Parameters from Jansa Seed Oil (Cussonia bateri) Using Artificial Neural Network
    AU  - Chinwe Priscilla Okonkwo
    AU  - Vincent Ishmael Egbulefu Ajiwe
    AU  - Ebuka Chidiebere Mmaduakor
    AU  - Njideka Veronica Nwankwo
    Y1  - 2022/02/16
    PY  - 2022
    N1  - https://doi.org/10.11648/j.ajac.20221001.12
    DO  - 10.11648/j.ajac.20221001.12
    T2  - American Journal of Applied Chemistry
    JF  - American Journal of Applied Chemistry
    JO  - American Journal of Applied Chemistry
    SP  - 7
    EP  - 14
    PB  - Science Publishing Group
    SN  - 2330-8745
    UR  - https://doi.org/10.11648/j.ajac.20221001.12
    AB  - Biodiesel has been referred to as a perfect substitute for diesel fuel due to its numerous promising properties. They are renewable, clean, increases energy security, improves the environment and air quality and also provides some good safety benefits. This study is focused on the investigation of the use of natural heterogeneous catalysts for production of biodiesel from jansa seed oil, as well as the implementation of artificial neural network (ANN) for the prediction of biofuel yield and process parameters. The biodiesel was produced through transesterification reaction by reacting jansa seed oil (FFA) with methanol (alcohol) to yield methyl ester. Waste periwinkle shell was prepared in 3 different forms; raw, calcined and acidified. The percentage yield of the methyl ester obtained were calculated and tabulated. The process parameters considered were methanol-oil mole ratio, catalyst concentration, agitation speed, reaction temperature and reaction time. The results of this research work revealed that the calcined periwinkle shell catalyst produced higher yield of biodiesel, compared to the yield obtained from the raw and acidified catalyzed process. The properties of the fatty acid methyl esters were within the standard range. The experimental and predicted yield were marginally the same. Hence, the model accurately predicted the yield with acceptable coefficient of determination and low mean squared error (MSE). The results demonstrate the flexibility of ANN model and the improvement of the model in terms of performance prediction when solving problems with stochastic dataset, especially the transesterification of biodiesel.
    VL  - 10
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Department of Pure and Industrial Chemistry, Nnamdi Azikiwe University, Awka, Nigeria

  • Department of Pure and Industrial Chemistry, Nnamdi Azikiwe University, Awka, Nigeria

  • Department of Pure and Industrial Chemistry, Nnamdi Azikiwe University, Awka, Nigeria