Natural fiber reinforced composite materials have been gaining popularity because, natural fibers are cheap and biodegradable. Pineapple leaf fiber (PALF) is a natural fiber and an agro waste. This PALF was treated with sodium hydroxide to clean the surface. 10%, 15%, 20%, 25% and 30% PALF based epoxy composites were fabricated by hand-lay-up technique. The mechanical properties such as tensile strength (TS), percentage of elongation at break (%Eb) and impact strength (IM) for composites were found to increase with increasing fiber content. The highest TS, %Eb and IM for 30% PALF based epoxy composite were 51.6 MPa, 15.882% and 14.189 Kg-cm respectively but tensile modulus (TM) was decreased with increasing fiber content. Degradation both in water and soil were done and the mechanical properties during degradation decreased a little bit over time because of the hydrophobic epoxy (matrix) material. 2.5 KGy, 5.0 KGy, 7.5KGy and 10 KGy gamma radiation doses were applied to composites and the effect of these doses were analyzed. For PALF based epoxy composite TS, TM, %Eb and IS values increased for certain value of gamma doses and for 7.5 KGy, these values were the highest while the values decreased in the increasing gamma radiation. Thermogravimetric analyses of PALF, epoxy and PALF based epoxy composite of non-radiated and irradiated composites materials were investigated. The thermogram of composite material was different than matrix materials as well as reinforced materials. The surface morphology of the reinforced, matrix and composite materials were investigated using scanning electron microscope (SEM).
| Published in | Advances in Applied Sciences (Volume 7, Issue 3) |
| DOI | 10.11648/j.aas.20220703.15 |
| Page(s) | 65-72 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2022. Published by Science Publishing Group |
Mechanical Properties, Thermo Gravimetric Analysis, SEM, Radiation Effect, Degradation
| [1] | McKenna, Henry A., John WS Hearle, and Nick O'Hear. Handbook of fibre rope technology. Vol. 34. Woodhead publishing, 2004. |
| [2] | Yan, Libo, Bohumil Kasal, and Liang Huang. "A review of recent research on the use of cellulosic fibres, their fibre fabric reinforced cementitious, geo-polymer and polymer composites in civil engineering." Composites Part B: Engineering 92 (2016): 94-132. |
| [3] | Todkar, Santosh Sadashiv, and Suresh Abasaheb Patil. "Review on mechanical properties evaluation of pineapple leaf fibre (PALF) reinforced polymer composites." Composites Part B: Engineering 174 (2019): 106927. |
| [4] | Munawar, Rose Farahiyan, Nurul Hayati Jamil, Mohd Khairul Shahril, Skh Abdul Rahim, Skh Muhammad, Zainal Abidin, Muhammad Zaimi, M. A. Azam, and Kok Tee Lau. "Development of green composite: pineapple leaf fibers (PALF) reinforced polylactide (PLA)." In Applied Mechanics and Materials, vol. 761, pp. 520-525. Trans Tech Publications Ltd, 2015. |
| [5] | Reddy, Narendra, and Yiqi Yang. "Biofibers from agricultural byproducts for industrial applications." TRENDS in Biotechnology 23, no. 1 (2005): 22-27. |
| [6] | Tomczak, Fábio, Kestur Gundappa Satyanarayana, and Thais Helena Demétrio Sydenstricker. "Studies on lignocellulosic fibers of Brazil: Part III–Morphology and properties of Brazilian curauá fibers." Composites Part A: Applied Science and Manufacturing 38, no. 10 (2007): 2227-2236. |
| [7] | Neto, Alfredo R. Sena, Marco AM Araujo, Fernanda VD Souza, Luiz HC Mattoso, and Jose M. Marconcini. "Characterization and comparative evaluation of thermal, structural, chemical, mechanical and morphological properties of six pineapple leaf fiber varieties for use in composites." Industrial Crops and Products 43 (2013): 529-537. |
| [8] | Vinod, B., and L. J. Sudev. "Effect of fiber orientation on the flexural properties of PALF reinforced bisphenol composites." International Journal of Science and Engineering Applications 2, no. 7 (2013): 166-169. |
| [9] | Mishra, S., M. Misra, S. S. Tripathy, S. K. Nayak, and A. K. Mohanty. "Potentiality of pineapple leaf fibre as reinforcement in PALF-polyester composite: Surface modification and mechanical performance." Journal of Reinforced Plastics and Composites 20, no. 4 (2001): 321-334. |
| [10] | Dhal, Jyoti Prakash, and Subash C. Mishra. "Processing and properties of natural fiber-reinforced polymer composite." Journal of Materials 2013 (2012). |
| [11] | Selamat, Mohd Zulkefli. "EFFECT OF BAMBOO FIBRE LENGTH ON THE PROPERTIES OF BAMBOO FIBRE/POLYPROPYLENE COMPOSITE." In Malaysia University Conference Engineering Technology. 2014. |
| [12] | Kasim, A., M. Selamat, N. Aznan, S. Sahadan, M. Daud, S. Salleh, and R. Jumaidin. "Effect of pineapple leaf fiber loading on the properties of pineapple leaf fiber–polypropylene composite." Proceedings of Mechanical Engineering Research Day 2015, no. 2015 (2015): 3-4. |
| [13] | Luo, S., and A. N. Netravali. "Interfacial and mechanical properties of environment-friendly “green” composites made from pineapple fibers and poly (hydroxybutyrate-co-valerate) resin." Journal of Materials Science 34, no. 15 (1999): 3709-3719. |
| [14] | Liu, Wanjun, ManjusriMisra, Per Askeland, Lawrence T. Drzal, and Amar K. Mohanty. "‘Green’composites from soy based plastic and pineapple leaf fiber: fabrication and properties evaluation." Polymer 46, no. 8 (2005): 2710-2721. |
| [15] | Potluri, Rakesh, V. Diwakar, K. Venkatesh, and B. Srinivasa Reddy. "Analytical model application for prediction of mechanical properties of natural fiber reinforced composites." Materials today: proceedings 5, no. 2 (2018): 5809-5818. |
| [16] | Lopattananon, Natinee, Kuljanee Panawarangkul, Kannika Sahakaro, and Bryan Ellis. "Performance of pineapple leaf fiber–natural rubber composites: The effect of fiber surface treatments." Journal of Applied Polymer Science 102, no. 2 (2006): 1974-1984. |
| [17] | Mohanty, A. K., M. A. Khan, and G. Hinrichsen. "Influence of chemical surface modification on the properties of biodegradable jute fabrics—polyester amide composites." Composites Part A: Applied Science and Manufacturing 31, no. 2 (2000): 143-150. |
| [18] | Jing, Bo, Wenli Dai, Shubai Chen, Tao Hu, and Pengsheng Liu. "Mechanical behavior and fracture toughness evaluation of K resin grafted with maleic anhydride compatibilized polycarbonate/K resin blends." Materials Science and Engineering: A 444, no. 1-2 (2007): 84-91. |
| [19] | Threepopnatkul, P., N. Kaerkitcha, and N. Athipongarporn. "Effect of surface treatment on performance of pineapple leaf fiber–polycarbonate composites." Composites Part B: Engineering 40, no. 7 (2009): 628-632. |
| [20] | Panyasart, Kloykamol, Nattawut Chaiyut, Taweechai Amornsakchai, and Onuma Santawitee. "Effect of surface treatment on the properties of pineapple leaf fibers reinforced polyamide 6 composites." Energy procedia 56 (2014): 406-413. |
| [21] | Castan, Pierre. "Process for the manufacture of thermosetting synthetic resins by the polymerization of alkylene oxide derivatives." U.S. Patent 2,444,333, issued June 29, 1948. |
APA Style
Md. Arif Hossain, Md. Sahadat Hossain, Ruhul A. Khan, A. M. Sarwaruddin Chowdhury. (2022). Preparation and Characterization of Pineapple Leaf Fiber Reinforced Epoxy Composite: Effect of Gamma Radiation. Advances in Applied Sciences, 7(3), 65-72. https://doi.org/10.11648/j.aas.20220703.15
ACS Style
Md. Arif Hossain; Md. Sahadat Hossain; Ruhul A. Khan; A. M. Sarwaruddin Chowdhury. Preparation and Characterization of Pineapple Leaf Fiber Reinforced Epoxy Composite: Effect of Gamma Radiation. Adv. Appl. Sci. 2022, 7(3), 65-72. doi: 10.11648/j.aas.20220703.15
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.aas.20220703.15,
author = {Md. Arif Hossain and Md. Sahadat Hossain and Ruhul A. Khan and A. M. Sarwaruddin Chowdhury},
title = {Preparation and Characterization of Pineapple Leaf Fiber Reinforced Epoxy Composite: Effect of Gamma Radiation},
journal = {Advances in Applied Sciences},
volume = {7},
number = {3},
pages = {65-72},
doi = {10.11648/j.aas.20220703.15},
url = {https://doi.org/10.11648/j.aas.20220703.15},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.aas.20220703.15},
abstract = {Natural fiber reinforced composite materials have been gaining popularity because, natural fibers are cheap and biodegradable. Pineapple leaf fiber (PALF) is a natural fiber and an agro waste. This PALF was treated with sodium hydroxide to clean the surface. 10%, 15%, 20%, 25% and 30% PALF based epoxy composites were fabricated by hand-lay-up technique. The mechanical properties such as tensile strength (TS), percentage of elongation at break (%Eb) and impact strength (IM) for composites were found to increase with increasing fiber content. The highest TS, %Eb and IM for 30% PALF based epoxy composite were 51.6 MPa, 15.882% and 14.189 Kg-cm respectively but tensile modulus (TM) was decreased with increasing fiber content. Degradation both in water and soil were done and the mechanical properties during degradation decreased a little bit over time because of the hydrophobic epoxy (matrix) material. 2.5 KGy, 5.0 KGy, 7.5KGy and 10 KGy gamma radiation doses were applied to composites and the effect of these doses were analyzed. For PALF based epoxy composite TS, TM, %Eb and IS values increased for certain value of gamma doses and for 7.5 KGy, these values were the highest while the values decreased in the increasing gamma radiation. Thermogravimetric analyses of PALF, epoxy and PALF based epoxy composite of non-radiated and irradiated composites materials were investigated. The thermogram of composite material was different than matrix materials as well as reinforced materials. The surface morphology of the reinforced, matrix and composite materials were investigated using scanning electron microscope (SEM).},
year = {2022}
}
TY - JOUR T1 - Preparation and Characterization of Pineapple Leaf Fiber Reinforced Epoxy Composite: Effect of Gamma Radiation AU - Md. Arif Hossain AU - Md. Sahadat Hossain AU - Ruhul A. Khan AU - A. M. Sarwaruddin Chowdhury Y1 - 2022/08/17 PY - 2022 N1 - https://doi.org/10.11648/j.aas.20220703.15 DO - 10.11648/j.aas.20220703.15 T2 - Advances in Applied Sciences JF - Advances in Applied Sciences JO - Advances in Applied Sciences SP - 65 EP - 72 PB - Science Publishing Group SN - 2575-1514 UR - https://doi.org/10.11648/j.aas.20220703.15 AB - Natural fiber reinforced composite materials have been gaining popularity because, natural fibers are cheap and biodegradable. Pineapple leaf fiber (PALF) is a natural fiber and an agro waste. This PALF was treated with sodium hydroxide to clean the surface. 10%, 15%, 20%, 25% and 30% PALF based epoxy composites were fabricated by hand-lay-up technique. The mechanical properties such as tensile strength (TS), percentage of elongation at break (%Eb) and impact strength (IM) for composites were found to increase with increasing fiber content. The highest TS, %Eb and IM for 30% PALF based epoxy composite were 51.6 MPa, 15.882% and 14.189 Kg-cm respectively but tensile modulus (TM) was decreased with increasing fiber content. Degradation both in water and soil were done and the mechanical properties during degradation decreased a little bit over time because of the hydrophobic epoxy (matrix) material. 2.5 KGy, 5.0 KGy, 7.5KGy and 10 KGy gamma radiation doses were applied to composites and the effect of these doses were analyzed. For PALF based epoxy composite TS, TM, %Eb and IS values increased for certain value of gamma doses and for 7.5 KGy, these values were the highest while the values decreased in the increasing gamma radiation. Thermogravimetric analyses of PALF, epoxy and PALF based epoxy composite of non-radiated and irradiated composites materials were investigated. The thermogram of composite material was different than matrix materials as well as reinforced materials. The surface morphology of the reinforced, matrix and composite materials were investigated using scanning electron microscope (SEM). VL - 7 IS - 3 ER -
Information
Email: