| Peer-Reviewed

Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms)

Received: 19 December 2017     Accepted: 2 January 2018     Published: 19 January 2018
Views:       Downloads:
Abstract

This paper presents design, simulation, fabrication and electrical analysis of a triple notched band UWB band pass filter. Short circuit stubs and microstrip line defected structures are used to design a triple notched band UWB filter. The proposed UWB BPF consists of five short circuited stubs of quarter wavelength attached to the feed line. The notched bands are created by introducing three U-shaped defected microstrip structures in the feed line. The proposed structure of the filter is designed, simulated on CST MSW and fabricated using conventional photolithography process. This band pass filter is designed to pass the UWB signals between 3.1 GHz to 10.6 GHz and to eliminate INSAT signal (4.6 GHz), WLAN signal (5.6 GHz) and satellite communication signal (8.0 GHz). The experimental results of this fabricated filter are compared with the simulated results and they are found to be in close agreement to each other. The Electrical equivalent circuit of this triple notched band filter is also presented in this paper and verified mathematically. This filter is compact in size and better in performance. It can be incorporated in UWB communication system to efficiently increase the interference protection from undesired signals. The physical dimension of this filter is about 30x10.5 mm2.

Published in International Journal of Wireless Communications and Mobile Computing (Volume 5, Issue 6)
DOI 10.11648/j.wcmc.20170506.11
Page(s) 32-44
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2018. Published by Science Publishing Group

Keywords

Ultra-Wide Band (UWB), Defected Microstrip Line Structure (DMS), WLAN, Multi-Mode Resonator (MMR), Federal Communication Commission (FCC), WiMAX, INSAT

References
[1] FCC, Revision of part 15 of the commission’s Rules regarding Ultra-wideband Transmission Systems, Federal Communications Commission, Tech, Rep, ET-Docket 98-153, FCC 02-48, Apr. 2002.
[2] Zhu, L. S. Sun, and W. Menzel, “Ultra-wideband (UWB) band pass filters using multiple-mode resonator,” IEEE Microw. Wireless Compon. Lett., Vol. 15, No. 11, pp. 796–798, 2005.
[3] R. Li and L. Zhu, "Compact UWB band pass filter using stub-loaded multiple-mode resonator," IEEE Microw. Wireless Compon. Lett., Vol. 7, No. 1, pp. 40 -42, 2007.
[4] Tianliang Zhang, Liguo Zhou, Kai Yang, Wei Dang, Kezhao Hua, Changlin Yang, Peng Chen, “Compact multi-mode UWB microstrip filter using meander resonator,” Microwave and Optical Technology Letters, Vol. No. 58, pp. 2026-29, 2016.
[5] Yong-Qin Liu and Xi-Zheng Ke, “A Novel Compact Microstrip UWB Band pass Filter with Improved Out-of-Band Rejection,” Progress In Electromagnetics Research Letters, Vol. 59, pp. 21–25, 2016.
[6] Hussein Shaman and Jia-Sheng Hong “An Optimum Ultra-Wideband (UWB) Band pass Filter with Spurious Response Suppression,” WAMICON 2006.
[7] Fallahzadeh, S. and M. Tayarani, “A new microstrip UWB band pass filter using defected microstrip structure,” Journal of Electromagnetic Waves and Application, Vol. 4 No. 7, pp. 893-902, 2010.
[8] Arjun Kumar and M. V. Kartikeyan, “Design and realization of microstrip filters with new defected ground structure (DGS),” Engineering Science and Technology, an International Journal, Vol. 20, No. 2, pp. 679-86, 2017.
[9] Naghshvarian-Jahromi, M. and M. Tayarani, “Miniature planar UWB band pass filters with circular slots in ground,” Progress in Electromagnetics Research Letters, Vol. 3, pp. 87-93, 2008.
[10] Yechou Lahcen, Tribak Abdelwahed, Kacim Mohamed, Zbitou Jamal, and Angel Mediavilla Sanchez, “A Novel Low-Cost Microstrip Band pass Filter for Ultra-Wideband RF Applications,” International Journal of Microwave and Optical Technology, Vol. 11, No. 2, March 2016.
[11] Abdel-Fattah Sheta and Ibrahim Elshafiey, “Microstrip Ultra-Wide-Band Filter,” PIERS Proceedings, Marrakesh, MOROCCO, March 20-23, 2011.
[12] Hong, J. S. and M. J. Lancaster, Microstrip Filters for RF/Microwave Application, Wiley, New York, 2001.
[13] Yang, G.-M., R. Jin, C. Vittoria, V.-G. Harris, and N.-X. Sun, “Small ultra-wideband (UWB) band pass filter with notched band,” IEEE Microw. Wireless Compon. Lett., Vol. 18, No. 3, pp. 176–178, 2008.
[14] Shaman, H. and J.-S. Hong, “Ultra-wideband (UWB) band pass filter with embedded band notch structures,” IEEE Microw. Wireless Compon. Lett., Vol. 17, No. 3, pp. 193–195, Mar. 2007.
[15] A. Kalteha, Atila Eskandarnejad, “Desighn of a Novel Compact Microstrip UWB Band-pass filter with 5.5 GHz band rejection function,” Indian J. Sci. Res. pp. 113-116, 2014.
[16] Tengfei Yana. Xiao-Hong, and Tanga, Jun Xiangb, “High-selectivity UWB band-pass filter with a notched band using stub-loaded multi-mode resonator,” AEU - International Journal of Electronics and Communications Vol. 70, Issue 12, pp. 1617-1621, 2016.
[17] P.-Y. Hsiao and R.-M. Weng, “Compact tri-layer Ultra-Wideband Band-Pass Filter with dual notch bands,” Progress In Electromagnetics Research, Vol. 106, pp. 49-60, 2010.
[18] L. Bala Senthil Murugan, S. Antony Anbu Raja, “Design and Implementation of a Microstrip Band-Stop Filter for Microwave Applications,” International conference on modeling, optimization and computing, Elsevier, Procedia Engineering pp. 1346 – 1351, 2012.
[19] Hung-Wei Wu and Yu-Fu Chen, “Ultra wideband band pass filter with dual-notched bands using stub-loaded rectangular ring multi-mode resonator” Microelectronics Journal, Vol. 43, Issue 4, pp. 257-62, 2012.
[20] Hung-Wei Wu and Yu-Fu Chen, “New compact ultra wideband band pass filter using modified multi-mode resonator” AEU - International Journal of Electronics and Communications, Vol. 66, Issue 12, pp. 1021-25, 2012.
[21] Anil Kamma, Ranjan Das, Darshak Bhatt, and Jayanta Mukherjee, “Multi-Mode Resonators Based Triple Band Notch UWB Filter,” IEEE Microwave and Wireless Components Letters, Vol. 27, Issue: 2, 2017.
[22] Chengpei Tang and Nian Yang, “Design of Compact Microstrip UWB Band pass Filter with Triple-Notched Bands,” Progress In Electromagnetics Research Letters, Vol. 58, pp. 9–16, 2016.
[23] Omid Borazjani, Mehdi Nosrati and Mojgan Daneshmand, “A novel triple notch-bands ultra wide-band band-pass filters using parallel multi-mode resonators and CSRRs,” International Journal of RF AND MICROWAVE COMPUTER-AIDED ENGINEERING, Vol. 24, Issue 3, pp. 375-81, 2014.
[24] Vijayakrishnan J. and Ravi Prakash Dwivedi, “Analysis of different shapes of defected microstrip structure (DMS) and their stop-band performance” ARPN Journal of Engineering and Applied Sciences Vol. 10, No. 8, 2015.
[25] Jian-Kang and Xiao Yu-Feng Zhu, “Multi-band band stop filter using inner T-shaped defected microstrip structure (DMS)” AEU - International Journal of Electronics and Communications, Vol. 68, Issue 2, February 2014, Pages 90–96.
[26] S. allahzadeh and M. Tayarani, “A New microstrip UWB band pass filter using defected microstrip structure” J. of Electromagn. Waves and Appl... Vol. 24. pp 893-902, 2010.
[27] Tao Jiang, Yanyan Wang and Ying Song Li “Design and Analysis of a Triple Stop-band Filter Using Ratioed Periodical Defected Microstrip Structure” Frequenz Journal of RF-Engineering and Telecommunications, June 2016.
[28] Hussein Shaman and Jia-Sheng Hong “Ultra-wideband (UWB) Microstrip Band pass Filter with Narrow Notched Band” Proceedings of the 38th European Microwave Conference EuMA pp. 857-60, 2008.
[29] Jianpeng Wang, Junding Zhao and Jia-Lin Li, “Compact UWB band pass filter with triple notched bands using parallel U-shaped defected microstrip structure,” Electronics Letters Vol. 50, Issue: 2, 2014.
[30] Satish Chand Gupta, Mithilesh Kumar and R. S. Meena “Design of UWB filter based on multi short circuited stubs” IEEE Conference RAECS, 2014.
[31] Koryn Ishii T. Handbook of microwave technology, component & devices, Vol. 01 Academic Press; 2013, pp. 123-124.
[32] J.-K. Xiao and W.-J. Zhu, “New Defected Microstrip Structure Band stop Filter” Progress In Electromagnetics Research Symposium Proceedings, pp. 12-16, 2011.
[33] Arjun Kumar, M. V. Kartikeyan “Design and realization of microstrip filters with new defected ground structure (DGS),” Engineering Science and Technology, an International Journal Volume 20, pp. 679-686, 2017.
[34] Shan, Q., C. Chen, and W. Wu, “Design of an UWB band pass filter with a notched band using asymmetric loading stubs,” IEEE International Conference on Microwave and Millimeter Wave Technology (ICMMT), Vol. 2, pp. 5–8, 2016.
[35] Ruifang Su, Ting Luo, Wenlan Zhang, Junding Zhao, and Zifei Liu “A New Compact Microstrip UWB Band pass Filter with Triple-Notched Bands,” Progress In Electromagnetics Research C, Vol. 60, pp. 187–197, 2015.
[36] Song, Y., G. M. Yang, and G. Wen, “Compact UWB band pass filter with dual notched bands using defected ground structures,” IEEE Microwave and Wireless Components Letters, Vol. 24, No. 4, pp. 230–232, 2014.
[37] Zhu, H. and Q. X. Chu, “Ultra-wideband band pass filter with a notch-band using stub-loaded ring resonator,” IEEE Microwave and Wireless Components Letters, Vol. 23, No. 7, pp. 341–343, 2013.
[38] Wei, F., Z. D. Wang, F. Yang, and X. W. Shi, “Compact UWB BPF with triple-notched bands based on stub loaded resonator,” IEEE Electronics Letters, Vol. 49, No. 2, pp. 124–126, 2013.
Cite This Article
  • APA Style

    Satish Chand Gupta, Mithilesh Kumar, Ram Swaroop Meena. (2018). Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms). International Journal of Wireless Communications and Mobile Computing, 5(6), 32-44. https://doi.org/10.11648/j.wcmc.20170506.11

    Copy | Download

    ACS Style

    Satish Chand Gupta; Mithilesh Kumar; Ram Swaroop Meena. Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms). Int. J. Wirel. Commun. Mobile Comput. 2018, 5(6), 32-44. doi: 10.11648/j.wcmc.20170506.11

    Copy | Download

    AMA Style

    Satish Chand Gupta, Mithilesh Kumar, Ram Swaroop Meena. Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms). Int J Wirel Commun Mobile Comput. 2018;5(6):32-44. doi: 10.11648/j.wcmc.20170506.11

    Copy | Download

  • @article{10.11648/j.wcmc.20170506.11,
      author = {Satish Chand Gupta and Mithilesh Kumar and Ram Swaroop Meena},
      title = {Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms)},
      journal = {International Journal of Wireless Communications and Mobile Computing},
      volume = {5},
      number = {6},
      pages = {32-44},
      doi = {10.11648/j.wcmc.20170506.11},
      url = {https://doi.org/10.11648/j.wcmc.20170506.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.wcmc.20170506.11},
      abstract = {This paper presents design, simulation, fabrication and electrical analysis of a triple notched band UWB band pass filter. Short circuit stubs and microstrip line defected structures are used to design a triple notched band UWB filter. The proposed UWB BPF consists of five short circuited stubs of quarter wavelength attached to the feed line. The notched bands are created by introducing three U-shaped defected microstrip structures in the feed line. The proposed structure of the filter is designed, simulated on CST MSW and fabricated using conventional photolithography process. This band pass filter is designed to pass the UWB signals between 3.1 GHz to 10.6 GHz and to eliminate INSAT signal (4.6 GHz), WLAN signal (5.6 GHz) and satellite communication signal (8.0 GHz). The experimental results of this fabricated filter are compared with the simulated results and they are found to be in close agreement to each other. The Electrical equivalent circuit of this triple notched band filter is also presented in this paper and verified mathematically. This filter is compact in size and better in performance. It can be incorporated in UWB communication system to efficiently increase the interference protection from undesired signals. The physical dimension of this filter is about 30x10.5 mm2.},
     year = {2018}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Design and Analysis of Triple Notched Band Uwb Band Pass Filter Using Defected Microstrip Structure (Dms)
    AU  - Satish Chand Gupta
    AU  - Mithilesh Kumar
    AU  - Ram Swaroop Meena
    Y1  - 2018/01/19
    PY  - 2018
    N1  - https://doi.org/10.11648/j.wcmc.20170506.11
    DO  - 10.11648/j.wcmc.20170506.11
    T2  - International Journal of Wireless Communications and Mobile Computing
    JF  - International Journal of Wireless Communications and Mobile Computing
    JO  - International Journal of Wireless Communications and Mobile Computing
    SP  - 32
    EP  - 44
    PB  - Science Publishing Group
    SN  - 2330-1015
    UR  - https://doi.org/10.11648/j.wcmc.20170506.11
    AB  - This paper presents design, simulation, fabrication and electrical analysis of a triple notched band UWB band pass filter. Short circuit stubs and microstrip line defected structures are used to design a triple notched band UWB filter. The proposed UWB BPF consists of five short circuited stubs of quarter wavelength attached to the feed line. The notched bands are created by introducing three U-shaped defected microstrip structures in the feed line. The proposed structure of the filter is designed, simulated on CST MSW and fabricated using conventional photolithography process. This band pass filter is designed to pass the UWB signals between 3.1 GHz to 10.6 GHz and to eliminate INSAT signal (4.6 GHz), WLAN signal (5.6 GHz) and satellite communication signal (8.0 GHz). The experimental results of this fabricated filter are compared with the simulated results and they are found to be in close agreement to each other. The Electrical equivalent circuit of this triple notched band filter is also presented in this paper and verified mathematically. This filter is compact in size and better in performance. It can be incorporated in UWB communication system to efficiently increase the interference protection from undesired signals. The physical dimension of this filter is about 30x10.5 mm2.
    VL  - 5
    IS  - 6
    ER  - 

    Copy | Download

Author Information
  • Department of Electronics Engineering, Rajasthan Technical University, Kota, India

  • Department of Electronics Engineering, Rajasthan Technical University, Kota, India

  • Department of Electronics Engineering, Rajasthan Technical University, Kota, India

  • Sections