| Peer-Reviewed

Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications

Received: 19 July 2017     Published: 19 July 2017
Views:       Downloads:
Abstract

A CPW-fed slot antenna with rhombus patch radiator is proposed for 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz wireless communication applications. The pentagon and rectangular slots are etched on the metallic layer of a single sided printed circuit board and rhombus patch radiator with a tuning stub in the feeding structure is embedded to form the proposed slot antenna. The dimensions of pentagon slot and tuning stub are changed to design and fabricate the antenna which can be operated at 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz successfully. IE3D software is used to design this CPW-fed slot antenna and choose the better parameters to manufacture the proposed antenna. The influences of slot and stub dimension parameters of the proposed antenna on resonant frequency, input reflection coefficient expressed in decibel and impedance bandwidth are described. The proposed antenna with the volume of 100mm×80mm×0.6mm has been fabricated. The measured result shows that the proposed antenna can be successfully operated at 1.2-2.8 GHz and 3.35-7.56 GHz bands. These bands are suitable for IoT-based applications.

Published in International Journal of Wireless Communications and Mobile Computing (Volume 5, Issue 2)
DOI 10.11648/j.wcmc.20170502.11
Page(s) 6-14
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2017. Published by Science Publishing Group

Keywords

CPW, Rhombus Patch, Pentagon Slot, IoT

References
[1] R. K. Raj, M. Joseph, B. Paul, and P. Mohanan, “Compact planar multiband antenna for GPS, DCS, 2.4/5.8 GHz WLAN applications” Electronics Letters, vol. 41, 2005, pp. 33-34.
[2] RongLin Li, Bo Pan, Joy Laskar, and Manos M. Tentzeris, “A compact broadband planar antenna for GPS, DCS-1800, IMT-2000, and WLAN applications,” IEEE Antennas Wireless Propag. Lett., vol. 6, 2007, pp. 25-27.
[3] J. EL Aoufi, N. Alaoui, M. Essaaidi, M. Benayad, “Design of a low cost planar antenna for 2.45 GHz RFID applications,” European Journal of Scientific Research, vol. 61, 2011, pp. 42–48.
[4] Y. Y. Lu, S. C. Wei, and H. C. Huang, “Design of RFID antenna for 2.45GHz applications,” Int'l Conf. on Innovative Comp., Information and Control, 2009, pp. 601-604.
[5] Y. L. Kuo and K. L. Wong, “Printed double-T monopole antenna for 2.4/5.2 GHz dual band WLAN operations,” IEEE Trans. Antennas Propag., vol. 51, 2003, pp. 2187–2192.
[6] Y. Y. Lu, S. C. Dai, and H. C. Huang, “Design of triple-band planar antenna for LTE/WLAN applications,” Int'l Conf. on Intell. Inform. Hiding and Multimedia Signal Proc., 2015, pp. 1–4.
[7] C. M. Wu, C. N. Chiu, and C. K. Hsu, “A new nonuniform meandered and fork-type grounded antenna for triple-band WLAN applications,” IEEE Antennas Wireless Propag. Lett., vol. 5, 2006, pp. 346-348.
[8] S. W. Qu, C. Ruan, and B. Z. Wang, “Bandwidth enhancement of wide-slot antenna fed by CPW and microstrip line,” IEEE Antennas Wireless Propag. Lett., vol. 5, 2006, pp. 15–17.
[9] J. Y. Sze, K. L. Wong, “Bandwidth enhancement of a microstrip-line-fed printed wide-slot antenna,” IEEE Trans. Antennas Propag., vol. 49, 2001, pp. 1020-1024.
[10] Y. Y. Lu, J. Y. Kuo, H. C. Huang, “Design and application of triple-band planar dipole antennas,” Journal of Information Hiding and Multimedia Signal Processing, vol.6, 2015, pp. 792-805.
[11] P. Xu, Z. H. Yan, C. Wang, “Multi-band modified fork-shaped monopole antenna with dual L-shaped parasitic plane,” Electronics Letters, vol. 47, 2011, pp. 364 – 365.
[12] H. D. Chen, “Broadband CPW-fed square slot antenna with a widened tuning stub,” IEEE Trans. Antennas Propag., vol. 51, No.8, 2003, pp. 1982–1986.
[13] J. Y. Chiou, J. Y. Sze, and K. L. Wong, “A broad-band CPW-fed strip-loaded square slot antenna,” IEEE Trans. Antennas and Propag., Vol. 51, No. 4, 719-721, 2003.
[14] Y. C. Lin, and K. J. Hung, “Compact ultrawideband rectangular aperture antenna and band-notched designs,” IEEE Trans. Antennas and Propag., Vol. 54, No. 11, 3075-3081, 2006.
Cite This Article
  • APA Style

    Yuh-Yih Lu, Yu-Ching Lin. (2017). Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications. International Journal of Wireless Communications and Mobile Computing, 5(2), 6-14. https://doi.org/10.11648/j.wcmc.20170502.11

    Copy | Download

    ACS Style

    Yuh-Yih Lu; Yu-Ching Lin. Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications. Int. J. Wirel. Commun. Mobile Comput. 2017, 5(2), 6-14. doi: 10.11648/j.wcmc.20170502.11

    Copy | Download

    AMA Style

    Yuh-Yih Lu, Yu-Ching Lin. Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications. Int J Wirel Commun Mobile Comput. 2017;5(2):6-14. doi: 10.11648/j.wcmc.20170502.11

    Copy | Download

  • @article{10.11648/j.wcmc.20170502.11,
      author = {Yuh-Yih Lu and Yu-Ching Lin},
      title = {Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications},
      journal = {International Journal of Wireless Communications and Mobile Computing},
      volume = {5},
      number = {2},
      pages = {6-14},
      doi = {10.11648/j.wcmc.20170502.11},
      url = {https://doi.org/10.11648/j.wcmc.20170502.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.wcmc.20170502.11},
      abstract = {A CPW-fed slot antenna with rhombus patch radiator is proposed for 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz wireless communication applications. The pentagon and rectangular slots are etched on the metallic layer of a single sided printed circuit board and rhombus patch radiator with a tuning stub in the feeding structure is embedded to form the proposed slot antenna. The dimensions of pentagon slot and tuning stub are changed to design and fabricate the antenna which can be operated at 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz successfully. IE3D software is used to design this CPW-fed slot antenna and choose the better parameters to manufacture the proposed antenna. The influences of slot and stub dimension parameters of the proposed antenna on resonant frequency, input reflection coefficient expressed in decibel and impedance bandwidth are described. The proposed antenna with the volume of 100mm×80mm×0.6mm has been fabricated. The measured result shows that the proposed antenna can be successfully operated at 1.2-2.8 GHz and 3.35-7.56 GHz bands. These bands are suitable for IoT-based applications.},
     year = {2017}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Design of CPW-Fed Slot Antenna with Rhombus Patch for IoT Applications
    AU  - Yuh-Yih Lu
    AU  - Yu-Ching Lin
    Y1  - 2017/07/19
    PY  - 2017
    N1  - https://doi.org/10.11648/j.wcmc.20170502.11
    DO  - 10.11648/j.wcmc.20170502.11
    T2  - International Journal of Wireless Communications and Mobile Computing
    JF  - International Journal of Wireless Communications and Mobile Computing
    JO  - International Journal of Wireless Communications and Mobile Computing
    SP  - 6
    EP  - 14
    PB  - Science Publishing Group
    SN  - 2330-1015
    UR  - https://doi.org/10.11648/j.wcmc.20170502.11
    AB  - A CPW-fed slot antenna with rhombus patch radiator is proposed for 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz wireless communication applications. The pentagon and rectangular slots are etched on the metallic layer of a single sided printed circuit board and rhombus patch radiator with a tuning stub in the feeding structure is embedded to form the proposed slot antenna. The dimensions of pentagon slot and tuning stub are changed to design and fabricate the antenna which can be operated at 1.2276/1.5754/1.8/2.4/2.45/5.0/5.2/5.8 GHz successfully. IE3D software is used to design this CPW-fed slot antenna and choose the better parameters to manufacture the proposed antenna. The influences of slot and stub dimension parameters of the proposed antenna on resonant frequency, input reflection coefficient expressed in decibel and impedance bandwidth are described. The proposed antenna with the volume of 100mm×80mm×0.6mm has been fabricated. The measured result shows that the proposed antenna can be successfully operated at 1.2-2.8 GHz and 3.35-7.56 GHz bands. These bands are suitable for IoT-based applications.
    VL  - 5
    IS  - 2
    ER  - 

    Copy | Download

Author Information
  • Department of Electrical Engineering, Minghsin University of Science and Technology, Hsinchu, Taiwan

  • Department of Electrical Engineering, Minghsin University of Science and Technology, Hsinchu, Taiwan

  • Sections