| Peer-Reviewed

Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material

Received: 10 July 2016     Accepted: 19 August 2016     Published: 30 August 2016
Views:       Downloads:
Abstract

A highly oil-absorptive Poly (methyl methacrylate-butyl acrylate)/ ATP–Fe3O4 magnetic composite resin was prepared by a conventional suspension polymerization using methyl methacrylate, and butylacrylate were used as monomers, and N, N-methylenebis acrylamide (MBA) as crosslinking agent and ammonium persulfate (APS) as initiator on the modified ATP–Fe3O4substrate. The optimum reaction condition was examined in detail. The results indicated that the prepared composite resin combined characteristics of stronger magnetism and higher oil absorbency. The resultant resin had high oil absorbency and the highest absorbencies respectively reaches 23.8, 25, 30.0, 32.6g.g for xylene, toluene, carbon tetrachloride and chloroform, which were higher than some oil absorptive materials previously reported. At the same time, it could easily be recovered and reused too. Kinetic investigation proved that the oil absorption obeyed the pseudo-first-order kinetic model and intraparticle diffusion model.

Published in American Journal of Polymer Science and Technology (Volume 2, Issue 1)
DOI 10.11648/j.ajpst.20160201.11
Page(s) 1-10
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2016. Published by Science Publishing Group

Keywords

High Oil-Absorption, Magnetic Composite Resin, Modified ATP–Fe3O4

References
[1] Özen, İ., Şimşek, S., & Okyay, G. (2015). Manipulating surface wettability and oil absorbency of diatomite depending on processing and ambient conditions. Applied Surface Science, 332, 22-31.‏
[2] Chun C. L., Park J. W. Oil spill remediation using magnetic separation [J]. J. Environ. Eng., 2001, 127: 443-449.
[3] Zhou M. H., Cho W. J. Synthesis and properties of high oil-absorbent 4-tert-butylstyrene-EPDM-divinylbenzene graft terpolymer [J]. J. Appl. Polym. Sci., 2002, 85: 2119-2129.
[4] Zhou M. H., Hoang T., Kim I. G., Ha C. S., Cho W. J. Synthesis and properties of natural rubber modified with stearyl methacrylate and divinylbenzene by graft polymerization [J]. J. Appl. Polym. Sci. 2001, 79: 2464-2470.
[5] Martel, B., Morcellet, M. Sorption of aromatic compounds in water using polymer sorbents containing amino groups [J]. J. Appl. Polym., Sc., 1994, 51: 443-451.
[6] Chin, W. C., Orellana, M. V., Verdugo, P. Spontaneous assembly of marine dissolved organic matter into polymer gels. [J]. Nature, 1998, 391: 568-572.
[7] Galindo-Gonzalez C., de Vicente J., Ramos-Tejada M. M., Lopez-Lopez M. T., Gonzalez- Caballero F., Duran J. D. G., Preparation and sedimentation behaviorin magnetic fields of magnetite covered clay particles [J]. Langmuir, 2005, 21: 4410- 4419.
[8] Murray H. H., Transitional and new applications for kaolin, smectite, and palygorskite: a general overview [J]. Appl. Clay Sci., 2000, 17: 207-221.
[9] Sanchez C. M., Sanchez M. M., Factors influencing interactions of organo phosphorus pesticides with montmorillonite [J]. Geoderma, 19836, 29: 107-118.
[10] Ainsworth C. C., Zachara J. M., Ln Schimidt R. Quinoline sorption on Na-montmorillonite: contribution of the protonated a d neutral species [J]. Clay Miner., 1987, 35: 121-128.
[11] Rodriguez J. M., Lopez A. J., Bruque S. Interaction of Fenamiphos with montmorillonite [J]. Clay Miner., 1988, 36: 284-288.
[12] Shu H. T., Li D., Scala A. A., Ma Y. H., Adsorption of small organic pollutants from aqueous streams by alumina silicate-based micro-porous materials [J]. Sep. Purif. Technol., 1997, 11: 27-36.
[13] Torrents A., Jayasundera S. The sorption of non-ionic pesticides onto clays and influence of natural carbon [J]. Chemosphere, 1997, 35: 1549-1565.
[14] Danis T. G., Albanis T. A., Petrakis D., Pomonis P. J., Removal of chlorinated phenols from aqueous solutions by adsorption on alumina pillared clay sand mesoporous alumina aluminum phosphates [J]. Water Res., 1998, 32: 295-302.
[15] Konstantinou I. K., Albanis T. A., Petrakis D. E., Pomoni P. J. s, Removal of herbicides from aqueous solutions by adsorption on Al-pillared clays, Fe-Al pillared clays and mesoporous alumina aluminum phosphates [J]. Water Res., 2000, 34: 3123-3136.
[16] Huang D. J., Wang W. B., Xu J. X., Wang A. Q. A comparative adsorption study of β-naphthol on four polymeric adsorbents from aqueous solutions [J]. Chem. Eng. J., 2012, 210: 166-172.
[17] Mu B., Wang Q., Wang A. Q. Preparation of magnetic attapulgite nanocomposite for the adsorption of Ag+ and application for catalytic reduction of 4-nitrophenol [J]. J. Mater. Chem. A, 2013, 1, 7083-7090.
[18] Liu Y. S., Liu P., Su Z. X., Li F. S., Wen F. S., Attapulgite–Fe3O4 magnetic nanoparticles via co-precipitation technique [J]. Appl. Surf. Sci., 2008, 255: 2020–2025.
[19] Jiang L. P., Liu P. Design of magnetic attapulgite/fly ash/poly (acrylic acid) ternary nanocomposite hydrogels and performance evaluation as selective adsorbent for Pb 2+ion [J]. ACS Sustainable Chem. Eng., 2014, 2: 1785-1794.
[20] Liese H. C., Am. Miner., 1967, 52: 1198.
[21] Shen, L., Lin Y. J., Du Q. G., Zhong W., Yang Y. L., Preparation and rheology of polyamide-6/attapulgite nanocomposite and studies on their percolated structure [J]. Polymer, 2005, 46: 5758-5766.
[22] Mikhaylova M., Kim D. Y., Bobrysheva N., Osmolowsky M., Semenov V., Tsakalakos T., Muhammed M., Super para magnetism of magnetic nanoparticles: Dependence on surface modification [J]. Langmuir, 2004, 20: 2472-2477.
[23] Flory P. J. Principles of Polymer Chemistry, Cornell University Press: Ithaca, NY, 1953
[24] Atta A. M., El-Ghazawy R. A. M., Farag R. K., et al. Swelling and Network Parameters of Oil Sorbers Based on Alkyl Acrylate and Cinnamoyloxy Ethyl Methacrylate Copolymers [J]. J. Polym. Res., 2006, 13: 257-266.
[25] Atta A. M., El-Hamouly, S. H., Alsabagh, A. M., Gabr, M. M., Crosslinked poly (octadecene-alt-maleic anhydride) copolymers as crude oil sorbers [J]. J. Appl. Polym. Sci., 2007, 105: 2113-2020.
[26] Zhou X. M., Chuai C. Z. Synthesis and characterization of a novel high-oil-absorbing resin [J]. J. Appl. Polym. Sci., 2010, 115: 3321-3325.
[27] Wu B., Zhou M. H. Sorption of styrene from aqueous solutions with oil absorptive resin [J]. J. Environ. Manage, 2009, 90: 217-221.
[28] Atta A. M., El-Ghazawy R. A. M., Farag R. K. Crosslinked reactive macro monomers based on polyisobutylene and octadecyl acrylate copolymers as crude oil sorbers [J]. React. Funct. Polym, 2006, 66: 931-943.
[29] Weber Jr. W. J., Morris J. C., Removal of biologically resistant pollutants from waste waters by adsorption in Advances in Water Pollution Research. Pergamon Press Oxford, 1962. p. 231.
[30] Weber Jr. W. J., Morris J. C. Kinetics of absorption of oil onto the super absorbent from solution [J]. J. Sanitary Eng. Div. Am. Soc. Civ. Eng., 1963, 89: 31-60.
[31] Wang X. H., Synthesis of acrylic high-oil absorption resins, Edited by Deng X. C. and Dong X. F., Adv. Mater. Res., 2012, 502: 222-226.
[32] Yoo S. Y., Daud W. M. A. W., Lee M. G. Preparation of a biodegradable oil absorber and its biodegradation [J]. Bioprocess and biosystems engineering, 2012, 35: 283-288.
[33] Atta A. M, El-Ghazawy R. A. M, Farag R. K., El-Kafrawy A. F., Abdel-Azim A. A. A. Crosslinked cinnamoyloxyethyl methacrylate and isooctyl acrylate copolymers as oil sorbers [J]. “Polymer international 54.7 (2005): 1088-1096.
[34] Li P. X., Yu B., Wei X. C. Synthesis and characterization of a high oil-absorbing magnetic composite material [J]. J. Appl. Polym. Sci., 2004, 93: 894-900.
[35] Feng Y., Xiao C. F. Synthesis and properties of highly oil-absorptive resin with hydroxyl ethylacrylate as potential crosslinking agent [J]. Chin J. React. Polym. 2006, 15 (1): 45-49.
[36] Wu K., Chu X. Z., zou S. Y., Zhao Y. J., Xing W. H. Preparation of highly oil absorptive resin poly (butyl methacrylate-styrene) and its oil absorption performance [J]. J. Chem. Eng. Chin. Univ., 2013, 23 (1): 76-83.
Cite This Article
  • APA Style

    Fathelrahman Mohammed Soliman, Wu Yang, Hao Guo, Mahgoub Ibrahim Shinger, Ahmed Mahmoud Idris, et al. (2016). Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material. American Journal of Polymer Science and Technology, 2(1), 1-10. https://doi.org/10.11648/j.ajpst.20160201.11

    Copy | Download

    ACS Style

    Fathelrahman Mohammed Soliman; Wu Yang; Hao Guo; Mahgoub Ibrahim Shinger; Ahmed Mahmoud Idris, et al. Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material. Am. J. Polym. Sci. Technol. 2016, 2(1), 1-10. doi: 10.11648/j.ajpst.20160201.11

    Copy | Download

    AMA Style

    Fathelrahman Mohammed Soliman, Wu Yang, Hao Guo, Mahgoub Ibrahim Shinger, Ahmed Mahmoud Idris, et al. Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material. Am J Polym Sci Technol. 2016;2(1):1-10. doi: 10.11648/j.ajpst.20160201.11

    Copy | Download

  • @article{10.11648/j.ajpst.20160201.11,
      author = {Fathelrahman Mohammed Soliman and Wu Yang and Hao Guo and Mahgoub Ibrahim Shinger and Ahmed Mahmoud Idris and Emtenan Suliman Hassan},
      title = {Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material},
      journal = {American Journal of Polymer Science and Technology},
      volume = {2},
      number = {1},
      pages = {1-10},
      doi = {10.11648/j.ajpst.20160201.11},
      url = {https://doi.org/10.11648/j.ajpst.20160201.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajpst.20160201.11},
      abstract = {A highly oil-absorptive Poly (methyl methacrylate-butyl acrylate)/ ATP–Fe3O4 magnetic composite resin was prepared by a conventional suspension polymerization using methyl methacrylate, and butylacrylate were used as monomers, and N, N-methylenebis acrylamide (MBA) as crosslinking agent and ammonium persulfate (APS) as initiator on the modified ATP–Fe3O4substrate. The optimum reaction condition was examined in detail. The results indicated that the prepared composite resin combined characteristics of stronger magnetism and higher oil absorbency. The resultant resin had high oil absorbency and the highest absorbencies respectively reaches 23.8, 25, 30.0, 32.6g.g for xylene, toluene, carbon tetrachloride and chloroform, which were higher than some oil absorptive materials previously reported. At the same time, it could easily be recovered and reused too. Kinetic investigation proved that the oil absorption obeyed the pseudo-first-order kinetic model and intraparticle diffusion model.},
     year = {2016}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Synthesis and Characterization of a High Oil-Absorbing Poly (Methyl Methacrylate-Butyl Acrylate)/ATP–Fe3O4 Magnetic Composite Material
    AU  - Fathelrahman Mohammed Soliman
    AU  - Wu Yang
    AU  - Hao Guo
    AU  - Mahgoub Ibrahim Shinger
    AU  - Ahmed Mahmoud Idris
    AU  - Emtenan Suliman Hassan
    Y1  - 2016/08/30
    PY  - 2016
    N1  - https://doi.org/10.11648/j.ajpst.20160201.11
    DO  - 10.11648/j.ajpst.20160201.11
    T2  - American Journal of Polymer Science and Technology
    JF  - American Journal of Polymer Science and Technology
    JO  - American Journal of Polymer Science and Technology
    SP  - 1
    EP  - 10
    PB  - Science Publishing Group
    SN  - 2575-5986
    UR  - https://doi.org/10.11648/j.ajpst.20160201.11
    AB  - A highly oil-absorptive Poly (methyl methacrylate-butyl acrylate)/ ATP–Fe3O4 magnetic composite resin was prepared by a conventional suspension polymerization using methyl methacrylate, and butylacrylate were used as monomers, and N, N-methylenebis acrylamide (MBA) as crosslinking agent and ammonium persulfate (APS) as initiator on the modified ATP–Fe3O4substrate. The optimum reaction condition was examined in detail. The results indicated that the prepared composite resin combined characteristics of stronger magnetism and higher oil absorbency. The resultant resin had high oil absorbency and the highest absorbencies respectively reaches 23.8, 25, 30.0, 32.6g.g for xylene, toluene, carbon tetrachloride and chloroform, which were higher than some oil absorptive materials previously reported. At the same time, it could easily be recovered and reused too. Kinetic investigation proved that the oil absorption obeyed the pseudo-first-order kinetic model and intraparticle diffusion model.
    VL  - 2
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Analytical Chemistry (Functional Materials), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, China

  • Analytical Chemistry (Functional Materials), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, China

  • Analytical Chemistry (Functional Materials), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, China

  • Analytical Chemistry (Photocatalysis), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, china

  • Analytical Chemistry (Photocatalysis), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, china

  • Analytical Chemistry (Functional Materials), College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, China

  • Sections